Learn more about Wedge Trombone Mouthpieces
- Silver Plated Brass Mouthpiece $230 (Gold Plated $340)
- Plastic Mouthpiece $110
- Silver Plated Brass Screw Rim $150 (Gold Plated $195)
- Plastic Screw Rim $110
- Brass Tone Modifier $50 (Silver Plated $75, Gold Plated $95)
- Silver Plated Brass (also available in gold plated brass)
- Range from 0.95 inches to 1.14 inches
- ID measured at .05 inches into the cup
- Wide range for every playing situation
- Depths from shallow E to extra deep XD
Wedge E Trombone Cup
- Shallow cup similar to Bach E.
- Bright sound with lots of projection.
- Suitable for Alto trombone.
- Preferred by some for extreme lead playing.
Wedge C Trombone Cup
- Typical shallow C trombone cup.
- Similar to Bach C cup.
- Good projection.
- Most effective with a small to medium diameter as beginner mouthpiece, or for lead trombone.
Wedge AL Trombone Cup
- Medium cup with a slightly funnel shape.
- Similar to Bach 6-1/2AL cup.
- Relatively dark sound from a medium cup.
- Good for intermediate players and players needing something between the shallow C cup and symphonic G cup.
Wedge GS Trombone Cup
- Intermediate between AL and G cup.
- Similar to Bach 5GS cup.
- Good combination of projection and lower register performance.
- More upper register support and projection than the G cup.
Wedge G Trombone Cup
- Medium deep cup similar to Bach 5G.
- Most popular model for mature players in a concert band or orchestral setting.
- Well balanced sound with even response in all registers.
- Works very well with larger diameters and slightly deeper cup for bass trombone.
Wedge D Trombone Cup
- Deeper cup for an extra full low register.
- Works well for second or third trombone when a big, dark sound is required.
- Well suited for bass trombone when a larger diameter is used.
Wedge XD Trombone Cup
- Extra deep cup for bass trombone.
- Huge sound and even response in all registers despite the deep cup.
Large and Small Shanks
- Our most popular standard Wedge trombone models currently available for tenor and bass trombone are shown in the comparison chart at the link below.
- We offer mouthpieces with the usual Small shank and / or Large shank, depending on the mouthpiece size.
- Remington shank mouthpieces are available for tenor sizes 100AL, 101GS, 101G 103G, and 104G.
- The Remington shank is a large shank with slightly slower Brown and Sharp taper compared to the regular Morse taper.
- It is used in certain (mostly vintage) tenor and bass trombones with a Remington receiver. Remington shanks were used in many vintage Conn large bore trombones starting in Elkhart, (1954-70) to Abilene, TX (1970-86) to Eastlake, OH (1986-92) Conn 8H, 88H, 60H, 62H, 70H-73H from around 1954 until the early 90’s.
- The modern 88H accepts a regular Morse taper mouthpiece.
- A Morse taper mouthpiece will not seat properly in a Remington receiver, and notes will not slot or speak as well as they would with a Remington shank mouthpiece.
- A Remington shank will not insert far enough into a regular receiver, and will wobble because the tip is larger than a regular large shank mouthpiece.
Medium European Shanks
- Medium European shanks for available for trombone sizes 100AL, 101G, 103G, 104G, and for all euphonium sizes.
- Some bass trombones, for example some vintage King models, have an extra deep receiver.
- If your mouthpiece inserts more than 1.25 inches (31 mm) into your leadpipe be sure to select the BT Deep Receiver option when ordering bass trombone mouthpieces.
Wedge trombone screw rims are avialable in silver or gold plated brass or Delrin plastic, and are compatible with Doug Elliott ST, LT, XT, SB, and LB cups.
Trombone Mouthpiece Comparison Table
Tenor and Bass Trombone Screw Rims
Trombone and Euphonium Tone Modifiers
Not sure which mouthpiece to choose? Call 1-877-679-3343